日韩女人性开放视频,性刺激的大陆三级视频,国产人碰人摸人爱视频,电家庭影院午夜

歡迎您訪問:瑞昌明盛自動化設備有限公司,我司將竭誠為您服務!
YASKAWA JEPMC-CM200伺服驅動電機現貨

主頁 > 產品中心 > RELIANCE

YASKAWA JEPMC-CM200伺服驅動電機現貨

類目:RELIANCE
型號:JEPMC-CM200
全國服務熱線:15270269218
手機:15270269218
微信:15270269218
QQ:3136378118
Email:3136378118@qq.com

在線咨詢
產品詳情
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等。
主營DCS控制系統備件,PLC系統備件及機器人系統備件,
優勢品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件

YASKAWA JEPMC-CM200伺服驅動電機現貨 YASKAWA JEPMC-CM200伺服驅動電機現貨 YASKAWA JEPMC-CM200伺服驅動電機現貨 YASKAWA JEPMC-CM200伺服驅動電機現貨
轉換器在其交流輸入端造成短時短路,因此
-稱為換向凹口。這種凹口低至0 V(100%)深度)可在變流器的次級繞組處接受
(專用)變壓器(無線路扼流圈運行)。然而
如果使用相同的變壓器供電,則必須減少其深度兩個以上功率相當?shù)霓D(zhuǎn)換器。在這種情況下,行扼流圈是必要的。它們必須引起大約1%的相對電壓
在額定電流下下降。如果出現以下情況,也需要使用所謂的1%扼流圈:與可用的相比,轉換器的功率非常低
變壓器或電源線的功率。ABB提供合適的1%窒息。
根據歐洲產品標準EN 61800-3
換向槽口必須保持低于線路電壓的20%
在一種環境中,規定了40%的上限
對于第二環境。這個目標可以通過線路阻塞的輔助。應用于這些扼流圈的電感
一個環境的值必須是網絡的4倍
轉換器連接點(公共點)處的電感耦合,PCC),如圖5.2-3所示。因此,在許多情況下
所謂的4%扼流圈是必要的,因此ABB也提供除了1%的扼流圈外,還需要合適的4%線路扼流器。通常,大電流不受變壓器限制,而是受連接工業區的電力電纜。因此,有必要詢問
關于線路阻抗和電流的能源供應公司
其在期望的公共耦合點(PCC)處可用。分離變壓器不需要線路扼流圈,因?yàn)椋浩渎└泻徒拥仄林g
繞組節省了EMC濾波器,參見1和4。屏幕和熨斗鐵芯必須與變流器的安裝板連接良好。如果變壓器位于變流器柜外屏蔽三相電纜的屏幕(環境,圖5.2-1右側)或接地電纜(“第二”環境,圖左邊的5.2-1)必須進行連接(另見24“連接示例”)。
6臺變流器(專用)變壓器
轉換器(專用)變壓器直接傳輸高功率
從中壓線路到單個大型轉換器或本地多個轉換器的低壓線路(見20)。此外,它還采取行動作為根據5所述的分離變壓器。
如果這種轉換器變壓器沒有屏幕,則EMC要求:然而,在大多數情況下,由于RF干擾能量很難通過中壓線路獲得公共線路至必須保護的負載的變壓器反對干擾。如有爭議,計量必須:在公共耦合點(公共低壓線)進行根據EN 61 800-3,可使用市場上可用的所有金屬機柜;然而根據9,其安裝板必須具有良好的導電表面。
如果驅動系統放置在多個機柜中,其安裝:板必須用寬大的導電板連接金屬
9.安裝板:安裝板必須由鋼制成,表面鍍鋅沒有任何繪畫。PE銅棒必須直接安裝在安裝板上,并且必須通過分布的多個螺栓與板連接沿其長度以相等的距離。
10.安置
裝置轉換器、線路扼流圈、保險絲、接觸器和EMC濾波器
放置在安裝板上,以便連接可以盡可能短,尤其是來自轉換器的通過線路扼流圈至過濾器,并滿足15中的要求滿足。待安裝的部件表面安裝板必須無涂層材料(見28)。Converters cause short-duration short circuits at their AC inputs, so
- called commutation notches. Such notches down to 0 V (100%
depth) can be accepted at the secondary windings of converter
(dedicated) transformers (operation without line chokes). However,
their depth must be reduced if the same transformer shall supply
more than two converters of comparable power. In such case line
chokes are necessary. They must cause about 1% relative voltage
drop at rated current. So - called 1% chokes are also necessary if
the power of the converter is very low compared with the available
power of the transformer or supply line. ABB offers suitable 1%
chokes.
According to the European product standard EN 61800-3, the
commutation notches must be kept below 20% of the line voltage
in the first environment, whereas an upper limit of 40 % is specified
for the second environment. This target can be achieved with the
aid of line chokes. The inductance of these chokes to be applied in
the first environment must have 4 times the value of the network
inductance at the converter’s connection point (point of common
coupling, PCC) as shown in Figure 5.2-3. Therefore in many cases
so-called 4% chokes are necessary, and therefore ABB offers also
suitable 4% line chokes besides the 1% chokes.Often the maximum current is not limited by the transformer but by the
power cable to the industry region. Therefore it is necessary to ask the
energy supply company concerning the line impedance and the current
which is available at the desired point of common coupling (PCC).A separation transformer makes line chokes unnecessary because
of its leakage inductance, and a grounded screen between its
windings saves an EMC filter, see 1 and 4. The screen and the iron
core must be well connected with the mounting plate of the converter. If the transformer is located outside the converter cubicle
the screen of a screened 3-phase cable ("first" environment, figure
5.2-1 at the right) or a ground cable ("second" environment, figure
5.2-1 at the left) must make this connection (see also 24 "Connection example").
6 Converter (dedicated) transformers
A converter (dedicated) transformer transfers high power directly
from a medium voltage line to a single large converter or to a local
low voltage line for several converters (see 20). Furthermore it acts
as separation transformer according to 5.
If such a converter transformer has no screen the EMC demands
are nevertheless fulfilled in most cases because the RF interference energy can hardly get via the medium-voltage line and the
transformer of the public line to the loads which must be protected
against pertubances. In the case of a dispute a measurement must
be done at the point of common coupling (public low - voltage line)
according to EN 61 800-3.All metal cubicles available on the market can be used; however,
their mounting plates must have well conducting surfaces according to 9.
If a drive system is placed in more than one cubicle their mounting
plates must be connected by broad pieces of well conducting sheet
metal.
9 Mounting plate The mounting plate must be made from steel with zinc surfaces
and without any painting. The PE copper bar must be mounted directly on the mounting plate without any insulating means between,
and it must be connected with the plate by several bolts distributed
in equal distances along its length.
10 Placement of
devices
The converter, the line choke, fuses, contactors and the EMC filter
are to be placed on the mounting plate so that the connections can
be made as short as possible, especially those from the converter
via the line choke to the filter, and that the requirements in 15 can
be fulfilled. The surface of the components to be mounted on the
mounting plate has to be free of coating material (see 28).