【主營產品】prefix = "o" ns = "urn:schemas-microsoft-com:office:office"
主營：世界知名品牌的PLC、DCS系統備件 模塊
①Allen-Bradley(美國AB)系列產品》
②Schneider(施耐德電氣)系列產品》
③General electric(通用電氣)系列產品》
④Westinghouse（美國西屋）系列產品》
⑤SIEMENS(西門子系列產品)》
⑥銷售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、
Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN
Robots。
⑦estinghouse（西屋）： OVATION系統、WDPF系統、MAX1000系統備件
。
⑧Invensys Foxboro（?？怂共_）：I/A Series系統，F(xiàn)BM（現場輸入
/輸出模塊）順序控制、梯形 邏輯控制、事故追憶處理、數模轉換、輸入/
輸出信號處理、數據通信及處理等。Invensys Triconex: 冗余容錯控制
系統、基于三重模件冗余（TMR）結構的zui現代化的容錯控制器。
⑨Siemens(西門子)：Siemens MOORE， Siemens Simatic C1，Siemens
數控系統等。
⑩Bosch Rexroth（博世力士樂）：Indramat，I/O模塊,PLC控制器,驅動
模塊等。
◆Motorola（摩托羅拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。
尊敬的顧客您好，為了更好的保障您的合法權益，購買前請仔細閱讀以下內容：
1.價格說明 并非原價，請以詢價為準。
價格說明 并非原價，請以詢價為準。
價格說明 并非原價，請以詢價為準。
2.由于市場波動頻繁，本店所標價格，并非實價，請買家提前咨詢 后再拍，感謝支持。
3.所售商品報價均為不含稅價 ，如須開票，請和店主聯系。
4.本店所售商品均為正品現貨，圖片實物拍攝。如果您訂購產品超過 多件，請與我們聯系，我們可以為您盡量提供折扣。
5本店產品分為全新原裝、全新無包裝，工程余貨和二手四種貨品。購買前請聯系客服仔細核對貨品、型號、數量。
6.本店所售商品保證質量，全新無包裝和二手商品簽收十五日出現問題均包退換，請放心購買。所有配件質保一年。因買家自己弄錯產品型號、參數或剪腳、上機、錯誤接入電源、錯誤安裝、保管不當、人為損壞等除外。
7.本店所售商品國內順豐包郵，國外運費自理。支持十五天內有任何產品質量問題退換貨，過期一切損失請自行承擔。請大家在貨物簽收時一定仔細檢查物品外觀是否完好無損，數量是否短缺，配件是否齊全如發現有任何問題請不要簽收并立即致電我們，貨物一旦簽收完畢，就代表雙方對貨物外表、數量、配件一致認可無爭議。
拍下商品后,視為認可以上各項條款，謝謝合作！
In the injection molding machine, the most widely used control law is proportional, integral, differential control, referred to as PID control. When the actual parameters of the pressure, speed and temperature of the injection molding machine can not be completely and reliably mastered, or the accurate mathematical model can not be obtained, and other technologies of the control theory are difficult to adopt, the parameters must be determined by experience and on-site debugging. At this time, the application of PID control technology is the most convenient. That is, when we do not fully understand the actual injection pressure, speed, temperature, or can not obtain the above parameters through effective measurement means, the most suitable PID control technology. PID control, there are also PI and PD control in practice. PID control is based on the error of the system, using proportional, integral and differential to calculate the control quantity.
Proportional control is the simplest control method. The output of the controller is proportional to the input error signal. When there is only proportional control, the system output has steady-state error.
In the integral control, the output of the control system is proportional to the integral of the input error signal. For a control system of injection molding machine, if there is steady-state error after entering steady state, it is said that the control system has steady-state error or system with steady-state error for short. In order to eliminate the steady-state error, "integral term" must be introduced into the pressure, speed and temperature control of injection molding machine. The error of the integral term depends on the integral of time. With the increase of time, the integral term will increase. In this way, even if the error is very small, the integral term will increase with the increase of time, which will promote the output of the injection molding machine computer to increase, and further reduce the steady-state error until it is equal to zero. Therefore, the proportional integral (PI) control can make the injection molding machine system into steady state without steady-state error.
