【主營產品】prefix = "o" ns = "urn:schemas-microsoft-com:office:office"

主營：世界知名品牌的PLC、DCS系統備件 模塊

①Allen-Bradley(美國AB)系列產品》

②Schneider(施耐德電氣)系列產品》

③General electric(通用電氣)系列產品》

④Westinghouse（美國西屋）系列產品》

⑤SIEMENS(西門子系列產品)》

⑥銷售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、

Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN

Robots。

⑦estinghouse（西屋）： OVATION系統、WDPF系統、MAX1000系統備件

。

⑧Invensys Foxboro（?？怂共_）：I/A Series系統，F(xiàn)BM（現場輸入

/輸出模塊）順序控制、梯形 邏輯控制、事故追憶處理、數模轉換、輸入/

輸出信號處理、數據通信及處理等。Invensys Triconex: 冗余容錯控制

系統、基于三重模件冗余（TMR）結構的zui現代化的容錯控制器。

⑨Siemens(西門子)：Siemens MOORE， Siemens Simatic C1，Siemens

數控系統等。

⑩Bosch Rexroth（博世力士樂）：Indramat，I/O模塊,PLC控制器,驅動

模塊等。

◆Motorola（摩托羅拉）：MVME 162、MVME 167、MVME1772、MVME177等系列。

尊敬的顧客您好，為了更好的保障您的合法權益，購買前請仔細閱讀以下內容：

1.價格說明 并非原價，請以詢價為準。
  價格說明 并非原價，請以詢價為準。

價格說明 并非原價，請以詢價為準。

2.由于市場波動頻繁，本店所標價格，并非實價，請買家提前咨詢      后再拍，感謝支持。

3.所售商品報價均為不含稅價 ，如須開票，請和店主聯系。

4.本店所售商品均為正品現貨，圖片實物拍攝。如果您訂購產品超過 多件，請與我們聯系，我們可以為您盡量提供折扣。

5本店產品分為全新原裝、全新無包裝，工程余貨和二手四種貨品。購買前請聯系客服仔細核對貨品、型號、數量。
6.本店所售商品保證質量，全新無包裝和二手商品簽收十五日出現問題均包退換，請放心購買。所有配件質保一年。因買家自己弄錯產品型號、參數或剪腳、上機、錯誤接入電源、錯誤安裝、保管不當、人為損壞等除外。
7.本店所售商品國內順豐包郵，國外運費自理。支持十五天內有任何產品質量問題退換貨，過期一切損失請自行承擔。請大家在貨物簽收時一定仔細檢查物品外觀是否完好無損，數量是否短缺，配件是否齊全如發現有任何問題請不要簽收并立即致電我們，貨物一旦簽收完畢，就代表雙方對貨物外表、數量、配件一致認可無爭議。

拍下商品后,視為認可以上各項條款，謝謝合作！

High speed product positioning is crucial to the success of printing. In order to achieve high-speed positioning, it is necessary to provide high-speed position locking input to the driver or motion controller, so as to capture the accurate spindle position when encountering the positioning mark. The difference between the front and back positions is used to calculate the actual distance between the positioning marks. That is, the distance is compared with the theoretical distance between the marks, and a correction amount is calculated. Then, the correction amount is substituted into the slave axis motion curve.

The time required from the detection of the positioning mark to the application of the correction amount is very important for the production of high quality products. This time is entirely dependent on the motion controller used for the application, and may also be affected by the technology used (for example, some digital motion control networks have a transport lag that must be compensated, which may not be acceptable in some applications). In some applications, it is necessary to use a special positioning algorithm, such as averaging the correction of several or many products, filtering the correction, or not applying the correction in some segments of the motion curve. The motion controller shall also be able to properly handle web splicing and missing positioning marks.

A typical 10 color printing line with basic configuration has more than 65 closed-loop motion control axes. In larger lines, there are usually more than 100 shafts. In the past, each axis was mechanically driven. Now, the updated control system improves the positioning performance and reduces the positioning accuracy to half of the old system. These control systems have high flexibility, can deal with special tasks, and provide unlimited variable repetition. Instead of the speed matching method discussed above, it enables the user to increase or decrease the speed of the plate roller relative to the web to change the repetition length.

These improvements can also make the speed faster, the maximum speed can be increased from 1200 FPM to 2000 FPM, flexographic printing process can achieve higher speed. The average time for a printer to switch from one task to the next is reduced from 4-6 hours to 30 minutes, or even less in some cases. The manipulator with motion control and printing driving device positioning system has a great influence on the switching time. In the application, because the whole control system provides better diagnostic information, the machine production time can be extended.